Log in
Register
Menu
Install the app
Install
Home
Forums
New posts
Datalogs
Records
Garage
New media
New comments
Resources
Latest reviews
Latest activity
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
What's new
Newest Posts
New media
New media comments
New resources
Latest activity
IQraceworks
replied to the thread
Kingtec forged piston
.
I cracked a piston ringland on my engine last year. Definitely caused by narrow rings gaps and lots of boost/heat. The factory ring...
Apr 16, 2024
ktb_e92
replied to the thread
Help setting up waste gate
.
Here's a picture regarding the routing. A 13psi wastegate spring will be good enough. As far as re-arranging the 2 wires in the ECU and...
Apr 16, 2024
ktb_e92
replied to the thread
F10 550i/335is clutch
.
It'll work, but what's your power goal?
Apr 16, 2024
CalvinNismo
reacted to
JPuehl's post
in the thread
I drove my car for the last time yesterday morning (Sunday 11/19/2023)...
with
Like
.
Getting quicker.
Apr 16, 2024
wheela
reacted to
JPuehl's post
in the thread
I drove my car for the last time yesterday morning (Sunday 11/19/2023)...
with
Like
.
The RPMs are based on the rollers, so it most likely shifted into 6th for a bit. In my logs it was only ~7k in 5th then shifted.
Apr 16, 2024
JPuehl
replied to the thread
N55 Dyno pulls
.
JPuehl has submitted a new record: Read more about this record...
Apr 16, 2024
JPuehl
replied to the thread
I drove my car for the last time yesterday morning (Sunday 11/19/2023)...
.
The RPMs are based on the rollers, so it most likely shifted into 6th for a bit. In my logs it was only ~7k in 5th then shifted.
Apr 16, 2024
Bnks334
replied to the thread
Injection needle for bedplate to block seal
.
the primer helps ensure the anerobic sealant seals better and activates/hardens. I wouldn't bother with the needle holes. Just put the...
Apr 16, 2024
wheela
reacted to
NoGuru's post
in the thread
Dual Mass Flywheel failure!
with
Like
.
Any chance you can grab a quick video before fixing, you know, for science :)
Apr 16, 2024
wheela
replied to the thread
Kingtec forged piston
.
Thanks in advance if you decide to test just the ring gap - costly risk, but good knowledge for the community👍
Apr 16, 2024
wheela
reacted to
mikesrex's post
in the thread
Kingtec forged piston
with
Like
.
I think I paid about 1100 for them. I ended up letting one of my buddies use them, and I think he will be building his motor soon. I...
Apr 16, 2024
wheela
replied to the thread
I drove my car for the last time yesterday morning (Sunday 11/19/2023)...
.
Go n55e😍😍😍
Apr 16, 2024
wheela
replied to the thread
I drove my car for the last time yesterday morning (Sunday 11/19/2023)...
.
Just noticed this dyno graph shows you ran her out to 7600rpm? Is this a mistake, or have you increased your redline?
Apr 16, 2024
wheela
reacted to
JPuehl's post
in the thread
I drove my car for the last time yesterday morning (Sunday 11/19/2023)...
with
Like
.
Getting quicker.
Apr 16, 2024
JPuehl
replied to the thread
I drove my car for the last time yesterday morning (Sunday 11/19/2023)...
.
Getting quicker.
Apr 16, 2024
Top
Bottom
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…